Oil spills at sea, harbours, beaches, or on land. Can also be used in industries. Bio-degradable Emulsifier with excellent efficiency and low toxicity with superior penetration. This product is specially designed for complete emulsification of oil by which subsequent dispersion takes place. APPLICATION :Oil spills at sea, harbours, beaches, or on land. Can also be used in industries.Application: Oil spills at sea, harbours, beaches, or on land. Can also be used in industries.Dose: Note: Biodegradable and having low toxicity . Self –life 5 YEARS( from mfr. date ) . HIGH – Emulsification rate Converts hydrocarbons particle  in to  very fine emulsions.Ready to use product. Suitable for Crude  / Bitumen / Residual  / Diesel / Kerosene, White spirit  & Lube oils etc .Effective  on oil spills at platefoprm , during loading or discharging of  cargo  or bunkers .For cleaning of spills on Deck, Ships side, Piers, Wharfs, etc. where allowed .  

The post Oil Spill Emulsifier first appeared on Fujairah chemical.

RXSOL Flocculant is a very effective liquid treatment based on  Poly chloride to separate oil residues from bilge water. It is iron-free, and is completely safe to the environment. Note : The product is to be used as a secondary flocculant along with the cationic primary flocculant for separator effluent oily water unit. the waste water is then treated in an air floatation unit.Application: International environmental regulations set strict rules as to the oil content in effluent water from ships. To meet these regulations, a combination of mechanical and chemical cleaning is necessary. Bilge Water Flocculant is used in combination with multistage bilge water cleaning systems that include mechanical separation of free oil, emulsion breaking, flocculation and filtration. After dosing, Bilge Water Flocculant breaks the oil-in-water emulsion created by contaminants in lubricating and fuel oils, emulsifying cleaning agents etc. It then destabilizes the remaining small oil droplets and agglomerates them into larger particles (flocs) that are easily collected by filtering.  Dose: Typical dose rate: 100 – 500ppm (0.1 – 0.5 litre/m3 of water) In a multistage bilge water cleaning system, Bilge Water Flocculant is fed undiluted through a dosage pump connected to the pressure side of the oil descaler. The floc tank is fed according to the flow of the bilge water pumped into it. The feed is adjusted in connection with the installation and normally needs no alteration. If required, dosing can also be controlled by measuring the level in the container.  Note: Features Cost-effective bilge water treatment based on specially selected Poly Aluminium Chloride Iron-free. Completely safe to the environment Acts by both breaking the oil-in-water emulsion and by building flocs Helps to meet environmental regulations on oil content. Discharged water contains normally less than 3 ppm oil Remaining oil sludge can be burned onboard or pumped ashore-contains very little water Low dosage, economical use Effective over an extended pH-range. Eliminates the use of pH-stabilising chemicals Approved by manufacturers of bilge water cleaning systems

The post FLOCCULANT 85113 first appeared on Fujairah chemical.

The post 2 Way Entry Non reversible Steel Reinforced Plastic Pallets first appeared on Fujairah chemical.

The post HDPE Injection Molded 4 Way Entry Double Deck Plastic Pallets-Export Range first appeared on Fujairah chemical.

The post HDPE Injection Molded 4 Way Entry Non Reversible One piece Molded Plastic Pallets first appeared on Fujairah chemical.

The post Heavy Duty 2 Way Entry Non reversible Plastic Pallet first appeared on Fujairah chemical.

The post 4 Way Entry Non Reversible Rackable Plastic Pallet first appeared on Fujairah chemical.

The post Single IBC Pallet first appeared on Fujairah chemical.

The post Spill Pallet 4 drum first appeared on Fujairah chemical.

The post Wire Mesh Fine first appeared on Fujairah chemical.