Activated Alumina Desiccants
More effective then ORDINARY alumina. Also refer new tec grade if ur requirement to absorb poisonous gases RXSOL-24-1905-025
Description
Activated alumina is highly porous material; this material can have a surface area significantly over 200 square metres/g. Very suitable for use as a filter of fluoride, arsenic and selenium in drinking water.
Application:
Activated Alumina Desiccants:
Activated Alumina Desiccants is a porous form of aluminum oxide. It has a high surface area which adsorbs vapors without any change in form. Activated Alumina Desiccants will not soften or disintegrate easily when immersed in water.
Dew points to -40°F and lower may be achieved with Activated Alumina Desiccants depending on dryer design and operating conditions.
The 1/8” (2-5mm) bead is the size most frequently used in regenerative dryers.
The 3/16” (4-8mm) bead is used when pressure drop and surface area requirements fall between 1/8” and 1/4” material. It is suitable for most systems.
The 1/4” (5-10mm) bead Activated Alumina Desiccants is used both as a pre-bed material to support large desiccant beds or as a buffer for silica gel beads. Pressure drop is slightly lower than 1/8” (25mm) material.
If size is not known or specified, the 1/8” (2-5mm) size is usually satisfactory. However, if Activated Alumina Desiccants is used in a regenerative dryer and the desiccant retaining screens cannot be measured, the 1/4” (5-10mm) size should be used as a bed support (6” layer). If at all possible, obtain a sample and measure it before ordering.
Product Benefits:
- High adsorption capacity. With high surface area and excellent pore distribution, Activated Alumina Desiccants has a high water adsorption capacity. This reduces initial cost, energy consumption and operating costs through smaller bed sizes and/or longer operating cycles.
- Low abrasion. Insures less dusting during tower depressurization or loading. Low abrasion means low pressure drop and a reduced chance of plugging the afterfilter.
- Resists liquid water. Water slugging due to upstream failure of aftercooler, separators or drain traps will not fracture the alumina beads. The adsorption capacity of the desiccant can be restored after complete regeneration.
- High crush strength. High crush strength, which limits dusting, is important during loading of desiccant towers. High crush strength makes alumina effective as a prebed material when used with other types of desiccants.
- Uniform bead sizes. Activated Alumina Desiccants is a uniformly sized bead. It provides low pressure drop to minimize channeling and ensures utilization of the full bed column section.
Physical Properties:
| 1/8” (2-5mm) | 3/16”(4-8mm) | 1/4” (5-10mm) | |
| Color and form | White bead | White bead | White bead |
| Bulk density | 48 lbs/Ft3 | 48 lbs/Ft3 | 48 lbs/Ft3 |
| Crush strength | 17-30 lbs | 145-60 lbs | 50-70 lbs |
| Surface area | 1.74 x 106 sq ft/lb | 1.65 x 106 sq ft/lb | 1.59 x 106 sq ft/lb |
|
Static adsorption Humidity |
– | – | – |
|
100% RH 90% RH 60% RH 10% RH |
42.0% 37.5% 21.0% 7.5% |
40.0% 35.0% 21.0% 7.0% |
36.0% 32.0% 17.5% 6.0% |
Dose:
Drier Chemicals manufacturer, importer and exporter of industrial chemicals and desiccants such as silica gel, activated alumina, activated carbon and carbon molecular sieves etc. Click on this link to get Most powerful GAS absorber.
Note:
Also refer more details of Impregnated Activated Alumina with potassium permagnate KMNO4.
Potassium Permanganate Impregnated Alumina has strong oxidizing property with Potassium Permanganate (KMnO4), it has good efficienty in removing Hydrogen Sulfide(H2S) , Chlorine(Cl2), Formaldehyde(HCHO), Nitric Oxide (NO) & Sulfur Dioxide(SO2) from air.
Additional information
| MSDS | Product Name RXSOL-19-1905-025 Product Type Activated Alumina Desiccants CHEMICAL NAME Aluminum Oxide Company Details: RX MARINE INTERNATIONAL Phone +91 22 65113333 / 5555 / 9999 Fax +91 22 2781 1318 :::AOH :0091 9821214367 PRODUCT IDENTIFICATION PRODUCT NAME: Activated Alumina INGREDIENTS COMPONENTS CAS NO. %BY WEIGHT ACGIH TLB OSHA PEL Aluminum oxide 1333-84-2 <97% N/D 15 (total dust), Aluminum silicate 14504-95-1 <0.2% N/D 5 (respirable) mg/m3
EYES: Can cause mild irritation, especially when wet. SKIN: Can cause mild irritation. INHALATION: Can cause mild upper respiratory tract irritation. INGESTION: Can cause mild irritation. Alumina is a low health risk by inhalation and should be treated as a nuisance dust as specified by the ACGIH. This product contains total silicates at <1% by weight. EYES: Flush eyes with plenty of water or saline for at least 15 minutes. Consult a physician. SKIN: Wash with soap and water for at least 15 minutes. Consult a physician if irritation persists. INHALATION: Remove to fresh air. Check for clear airway, breathing, and presence of pulse. Provide CPR for persons without pulse or respirations. Consult a physician. INGESTION: If swallowed, dilute by drinking large amounts of water. Never give,anything by mouth to a convulsing or unconscious person. Do not induce vomiting. Consult a physician. SUITABLE EXTINGUISHING AGENTS: Use fire fighting measures that suit the environment. PROTECTIVE EQUIPMENT: Wear self-contained respiratory protective device. Wear fully protective suit. ACCIDENTAL RELEASE MEASURES: Person-related safety precautions: Wear protective clothing. Alumina is a low health risk by inhalation and should be treated as a nuisance dust as specified by the ACGIH. This product contains total silicates at <1% by weight. HANDLING: Ensure good ventilation/exhaust at the workplace. Prevent formation of dust. Provide suction extractors if dust is formed. Protection against explosions and fires: No special measures required. STORAGE: Keep material dry. Storage in one common storage facility is not required. Personal protective equipment. Do not inhale dust. Avoid contact with the eyes. Use suitable respiratory protective device in case of insufficient ventilation. APPEARANCE: Off-white, crystalline or gelatinous granules, pellets. BOILING POINT: Undetermined FREEZING POINT: 3,700°F (2038°C) VAPOR PRESSURE: Not applicable AUTOIGNITING: Product is not self igniting SPECIFIC GRAVITY: 3.2 DENSITY: Loose Bulk: 39-52 lb/ft (0.62-0.83 g/cm ). pH: 10% in water 9.4-10.1 ODOR: Characteristic CHEMICAL STABILITY CONDITIONS TO AVOID A rise in temperature may result from contact with water. INCOMPATIBILITY None. HAZARDOUS DECCSIPOSITION PRODUCTS None if used according to specifications. HAZARDOUS POLYMERIZATION: None. Non-corrosive. N/A N/A Collect in containers, bags, or covered dumpster boxes. If reuse or recycling is not possible, material may be disposed of at an industrial landfill. Waste disposal key: 16 03 01 513 05 N/A NA the above information is accurate to the best of our knowledge.however, since data, safety standards, and government regulations are subject |
|---|
